Blakeslee DD-8 Manuel d'utilisateur

INSTALLATION & OPERATIOND-8 & DD-8 DISHWASHERS(01-13)

— 10 —Rough-in Diagrams – Model D-8Tankinside26"660mmWALLTanksideto reartrack23-3/4"600mmSplash guard recommendedRIGHT SIDE OF UNIT ALWAYS F

— 11 —Rough-in Diagrams – Model DD-8Tankinside23-1/2"595mmWALLTankinsideHoodoutside6-1/2"165mmBetweentracks20"510mm3"75mm25-3/16&q

— 12 —Pilot Flame AdjustmentThe pilot ame should engulf the tip of the pilot sensing thermocouple. 3/8" to 1/2"ThermocoupleCorrect ame adj

— 13 —K1K1L1Ground5*2FUSEN.O.DISPENSERTRANSFORMERThe designated wire connections for the dispensers are found in the control box. #2 is common; the sw

— 14 —OPERATIONPreparing the Dishwasher for Use1. Close the drain by turning the drain valve handle clockwise as far as it will go.Drain line to sewe

— 15 —Automatic Start (Optional)When the dishwasher is equipped with this feature, a cycle is initiated automatically when the door closes.Manual Star

— 16 —Operating the DishwasherOnce the wash tank has been lled and the detergent added (for units with optional Wash Cycle Timer, set the wash cycle

— 17 —StandpipeStandpipeGuideStandpipeScreenStandpipe Guide5. Thoroughly wash and rinse the interior of the dishwasher. Pay special attention to the

— 18 —MAINTENANCEMotorNo lubrication required.PumpNo lubrication required.Doors/HoodNo lubrication required.Line StrainersWater inlet (and steam line,

— 19 —Pump Motor Overload ProtectionWash pump motor protection is provided by thermal overload relay(s) located in the control box. In the event the p

— 2 —ELECTRICAL WARNINGSTHIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD ST

— 20 —TROUBLESHOOTINGPROBLEM PROBABLE CAUSES CORRECTIVE ACTIONPump motor will not start Overload trippedClear pump impeller.Reset relay.Machine will n

— 21 —PROBLEM PROBABLE CAUSES CORRECTIVE ACTIONPoor rinse resultsRinse nozzles clogged Clear rinse nozzles.Line strainer cloggedTurnowatersupply.

— 22 —EQUIPMENTGROUNDCTG LEQUIPMENTGROUNDG L208 / 240 VAC1 PHASE 60 HZSUPPLY LINES208 / 240 / 480 VAC3 PHASE 60 HZSUPPLY LINESHCHTRHTROLHTROLHCO

— 23 —SYM. DESCRIPTIONTB Terminal BlockGL Ground LugMC 25A Motor ContactorOL Overload RelayMTR 1.5 HP Motor 208-240/480V, 3 PH, 60Hz 1.5 HP Mot

— 24 —208 / 240 / 480 VAC3 PHASE 60 HZSUPPLY LINESHTRMCOLEQUIPMENTGROUNDCTTBG LL 3L 3L 2L1T 3L 2T 2T 1HTRMCOLL 3L1T 3L 2T 2T 1L 1BOOSTERCONTROLCYCL

— 25 —SYM. DESCRIPTIONTB Terminal BlockGL Ground LugMC 25A Motor ContactorOL Overload RelayMTR 1.5 HP Motor 208-240/480V, 3 PH, 60Hz 1.5 HP Moto

— 26 —USA Date of Installation ________________________________ Serial No. Model No. _____________________ _____________________ Lim

— 27 —Notes

1228 Capitol DriveAddison, IL 60101Phone: 630-532-5021Fax: [email protected]

— 3 — WARNING: Before performing any service that involves electrical connection or disconnection and/or exposure to electrical components, always per

— 4 —TABLE OF CONTENTSGENERAL DESCRIPTION ...

— 5 —GENERAL DESCRIPTIONModel D-8The Model D-8 door-type commercial dishwasher has a three-sided door or hood that is spring counterbalanced and opens

— 6 —INSTALLATIONVisual Inspection Before installing the unit, inspect the shipping container and machine for damage. A damaged container may indicate

— 7 —WasherHoodGapTruss head screws,lockwashers and nutsTableS/SAttach Table to Tank22" MIN.23-3/8"DISHTABLE DIMENSION INFORMATIONLEFT SIDE

— 8 —Pump Motor Rotation WARNINGBefore performing any service that involves electrical connection or disconnection and/or exposure to electrical compo

— 9 —Electric Heater WARNINGBefore performing any service that involves electrical connection or disconnection and/or exposure to electrical component